Define whether walls are Load bearing or Non load bearing
Default wall width
Define wall width
Default top elevation of wall
Define default top elevation
Default bottom elevation of wall
Define default bottom elevation
Standard Heel Heights
Define heel height size
Custom Heel Height; set to '0' to use standard heel heights
Define heel height or use 0 for standard heel height
Heel height measured at outside of Fascia
Define how heel height is measured
When multiple pitches are used on the same roof, adjustments must be made to the heel heights or overhang lengths to get the fascia to line up. The point for fascia alignment is the outside of the fascia and not the end of the truss overhang. This setting provides the ability to define the outside of the fascia and have the truss overhangs stop at the inside of the fascia. Note that this check box is only enabled if the Fascia Adjustment is not set to "None" and the overhang is less than or equal to the fascia thickness input in the Fascia Adj drop down list.
Cant dimension
Define default cantilever dimension. None should be used only on interior walls with no planes attached. Exterior walls with planes must have a cant and overhang attached to them; use the 00-00 setting for exterior walls with planes.
Overhang Length
Default value for a wall to have a specified overhang length. None should be used only on interior walls with no planes attached. Exterior walls with planes must have a cant and overhang attached to them; use the 00-00 setting for exterior walls with planes.
OH: How measured?
Dimension for overhangs:
- OutPnt for farthest top chord point
- InPnt for the farthest inside point of the top chord
- Rake for the rake
OH: End Cut
Set overhang end cut as follows:
- Plumb
- Square
- Angle
- Seat (previously DblCut)
- Fascia
Note: When a left and/or right overhang on a rafter is set to zero (0) this setting is not applied to that end of the rafter and a Plumb cut is used instead. This setting is applied on any overhang value of 1/16 or higher.
OH: Angle 1
Define overhang for first angle
OH: Angle 2
Define overhang for second angle
OH: Length of Seat or Fascia Cut
Define length of seat cut or fascia cut
Fascia Adjustment; set to '0' for None
Adjust fascia or use 0 for none
Attach Roof Plane to wall
Auto-attach a roof plane to a wall if set to True
Attach Ceil Plane to wall
Auto-attach a ceiling plane to a wall if set to True
Attach Roof Plane to work line
Auto-attach roof plane to workline if set to True
Attach Ceil Plan to work line
Auto-attach ceiling plane to workline if set to True
Roof pitch from wall
Define roof pitch for a wall
Ceiling pitch from wall
Define ceiling pitch for a wall
Roof pitch from work line
Define roof pitch for a workline
Ceiling pitch from work line
Define ceiling pitch for a workline
Hip Drop Dim for flat TC segments
Define hip drop for flat top chord
Wall veneer
Enable veneer for a wall
Beam veneer
Enable veneer for a beam
Default veneer width
Define default width of veneer
Gap between wall and veneer
Define gap distance between the wall and the veneer
Veneer is load bearing
Specify whether veneer is load bearing
Veneer to match wall elevation
When set to True, veneer will be created at the same top and bottom elevation as the wall.
Default top elevation of veneer
Define the top elevation of the veneer; this does not have to be the same elevation as the top of the wall.
Default bottom elevation of veneer
Define the bottom elevation of the veneer; this does not have to be the same elevation as the top of the wall.
Defining edge is the veneer
When enabled, the distance input in the Layout Commands text box on the Settings dialog defines the length of the wall to the outside of the veneer and not to the outside of the wall.
Plane Indicators
Plane tag size, or 0 to disable
Specify size of the plane tag
Display pitch in tag
Display the pitch in the plane tag
Circle walls - min wall length
Minimum length of arc wall
Wall Colors by Elevation
Wall Data
Display available data for a wall
Walls are colored by elevation
When set to True, define colors for walls based on elevation.
Bolds Inside line of load bearing walls
When set to True, the inside line of load bearing walls displays in bold.
Truss Colors by Type
Define/edit these colors using the Color Settings dialog. Settings are not editable in EnvData. See Define Truss Type Colors.
Girder
Girder color
Gable
Gable color
Hip Girder
Hip Girder color
Secondary Hip Girder
Secondary Hip Girder color
Jack
Jack color
Corner Girder Truss
Corner Girder Truss color
Corner Rafter
Corner Rafter color
Stacked Corner Rafter
Stacked Corner Rafter color
Rafter
Rafter color
Stacked Rafter
Stacked Rafter color
Valley Truss
Valley Truss color
Layin Gable
Laying Gable color
Shear Panel
Shear Panel color
Color Trusses by Type
When set to True, define colors for walls based on elevation.